Analogue-solutions Cranial Saw Bedienungsanleitung PDF herunterladen

GLIDE Control / Switch

The rotary control sets the Glide

(portamento) time for both s.VCO

But if the Toggle switch is up, then

Glide is only applied to 2.VCO

The normal mode would be down

so Glide works on both VCOs.

Scaling for VCO1 will be a little

out when Glide for VCO1

removed since a whole circuit

gets disconnected - but this

should not be an issue since this

mode is more for sound effects.

TUNE Slider

This slider sets pitch for both

VCOs

MIX Output

This is the audio output from

the mixer. Signal sources for

the mixer are each and VCO

the Sub Osc.

VCO VCO1 / 2 Square Wave Outputs

These are the square ( ) audio PW

outputs from each , pre-mider.VCO

PITCH CV input

This is the main pitch CV

input. It will affect both

VCOs, and is sent pre-

Glide.

MOD CV Inputs

These input sockets allow the pitch of each to be CV VCO

modulated. The lower socket is a direct input.

The signal sent to the upper socket can be attenuated using

the slider.BOTH

SYNC

When the switch is

up Sync is VCO

enabled. When

enabled the Detune

range is increased

to allow extremee

-12V

+12V

+5V (if ﬁtted in your case)

n/a

key

pin1

Power connector as found on Medic Modules

Speciﬁcation;

Width: 38HP

Depth: 25mm

Weight: 285g

Voltage: -/+12V

Power Consumption: +12V, 15mA / -12V, 28mA

Doepfer style power cable included.

Screws not included.

Mounting/Connection tips;

The supplied power cable is keyed.

That means it can only be ﬁtted one

way! (Unless you use excessive force).

Pin one is at the top on our modules

(Doepfer ﬁt their sockets upside-

down).

Medic Modules use a 14 pin 'boxed'

header on the .PCB

The two ends of the power cable are

different. Plug the 14pin socket end

into the Module power header.

Plug the larger 16pin socket into

your case power supply.

Note: Physically disconnect your

power supply/case from the mains

electricity.

Ensure you connect up the module

correctly!

Ensure it is screwed into the case.

Ensure no metal parts can short out

the solder joints on the rear.

Ensure your case is 100% functional

before ﬁtting the module.

It has been found over the last 15

years of making modules, that around

90% of module problems have typically

the following user problems;

Power cable connected wrong,

faulty power supply, other poor quality

modules ﬁtted in the case affecting

other modules.

cranial saw dual vco

Cranial Saw is a dual with Sync, Sub Osc, Glide, Cross mod and more!VCO

It is based on modiﬁed old circuit designs from the mid 1970s - giving a very full and vintage

sound.

VCO VCO PW1 / 2 Inputs

Each has a Pulse Width input, to allow VCO CV

external control over the pulse width of each

VCO's square wave.

VCO FREERUN1

When this switch is up,

then will no longer VCO

track the input PITCH CV

socket.

PW PW1 & 2 Sliders

These two sliders allow the

pulse width of each 's VCO

square wave to be manually

set.

DETUNE Slider

This slider is used to

detune 2 relative to VCO

VCO1.

SUBOSC Output

This is the audio output from

the Sub Osc, pre-mixer.

WAVE Switches

The position of these swiches

determines whether each

VCO's saw or square wave is

sent to the mixer.

VCO2 Mod Slider

This slider is used to

attenuate the signal CV

patched to the VCO CV2

socket below.

VCO VCO SUB1 / 2 / Sliders

These sliders set the level of

the above audio sources that

are sent to the mixer.

1 2 3

Sub-Oscillator 2
modules 3

Inhaltsverzeichnis

Seite 1

GLIDE Control / SwitchThe rotary control sets the Glide (portamento) time for both s.VCOBut if the Toggle switch is up, then Glide is only applied to

Seite 2 - Sub-Oscillator

Controls In More Detail and Setup IdeasTUNE sliderThis is the master tune control to change the pitch of both VCOs.DETUNE sliderThis slider allows you

Seite 3 - modules

cranial saw modulesmedicdual vco / subTUNE DETUNE PW1BOTH VCO2PW2VCO1VCO2 SUBPW PW VCO1 VCO2 MIXPITCH MODMODCVCVOUTOUTGLIDEFREERUN1+2VCOSYNCWAVE WAVEM

Kommentare zu diesen Handbüchern

Keine Kommentare

Analogue-solutions Cranial Saw Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Audio-Zubehör Analogue-solutions Cranial Saw herunter. Analogue Solutions Cranial Saw User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Audio-Zubehör Analogue-solutions Cranial Saw